Graco-inc 224200 Instrukcja Użytkownika

308131Rev. R0365Part No. 224200 shownNOTE: Any modification of genuine Graco parts or replacement of parts with non-Graco parts will void agency appro

10 308131Notes

308131 11OperationPressure Relief ProcedureWARNINGPRESSURIZED EQUIPMENT HAZARDThe system pressure must be manually relieved toprevent the

12 308131Operation0369AFig. 40365201264543g31DD43cSelecting a Fluid Nozzle and Air CapWARNINGPRESSURIZED EQUIPMENT HAZARDTo reduce the risk

308131 13OperationOperating the Spray Gun (continued)1. Follow the Operating Checklist on page 11.2. To adjust the air cap for a vertical

14 308131OperationShutdownWARNINGPRESSURIZED EQUIPMENT HAZARDTo reduce the risk of an injury, follow the PressureRelief Procedure on page 1

308131 15MaintenanceClean the Air Cap and Fluid NozzleCAUTIONDo not use metal tools to clean the air cap or spraytip holes as this could s

16 308131TroubleshootingWARNINGELECTRIC SHOCK HAZARDInstalling and servicing this equipmentrequires access to parts which maycause an elect

308131 17TroubleshootingGun Operation TroubleshootingProblem Cause SolutionFluid leakage from the fluid packingareaThe needle packings or

18 308131TroubleshootingElectrical TroubleshootingProblem Cause SolutionPoor wrap-around The ES ON-OFF lever is in the OFF (O)position.*Tur

308131 19TroubleshootingElectrical Troubleshooting with SVRNOTE: Additional gun troubleshooting can be done using the Remote Spraying Volt

2 308131

20 308131Electrical TestsThe performance and safety of the spray gun aredirectly affected by the condition of the electricalcomponents cont

308131 21Electrical TestsTest Power Supply Resistance (See Fig. 9)Remove the power supply (18) from the gun. SeePower Supply Removal and

22 308131ServicePrepare the Gun for ServiceWARNINGELECTRIC SHOCK HAZARDInstalling and servicing this equipmentrequires access to parts that

308131 23ServiceAir Cap/Nozzle/Resistor Stud Replacement(continued)6. Trigger the gun while installing the fluid nozzle (21)and resistor s

24 308131ServiceBarrel Removal1. Prepare the gun for service as instructed on page22.2. Carefully loosen the nut (14) from the bracket/flui

308131 25ServiceFluid Packing Removal1. Prepare the gun for service as instructed on page22.2. Remove the air cap assembly, fluid nozzle a

26 308131ServiceFluid Packing Rod RepairThe fluid packing rod can be replaced as individualparts or as an assembly. The overall assembly is

308131 27ServiceFig. 1873537a37b18a1837F318b18c18fG Apply a very light coat of lubricant Do not expose to solvents0384BBPower Supply

28 308131ServiceTurbine Alternator Removal and ReplacementNOTE: Replace turbine bearings after 2000 hours ofoperation. See your authorized

308131 29ServiceFan Air Adjustment Valve Repair1. Prepare the gun for service as instructed on page22.2. Place a wrench on the flats of th

308131 3Table of ContentsSymbols 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnings 4. . . . . . . . .

30 308131ServiceFluid Adjustment Assembly Repair1. Prepare the gun for service as instructed on page22.2. Using a 14 mm socket wrench, remo

308131 31ServiceAir Trigger Valve Repair1. Prepare the gun for service as instructed on page22.2. Using a 14 mm socket wrench, remove the

32 308131ServiceES ON-OFF Valve Repair1. Prepare the gun for service as instructed on page22.2. Loosen the set screw (24) with the 2 mm hex

308131 33Notes

34 308131Parts28c28a*28d*28e*28hDETAIL A1, 75822221*25See Detail A28b2043b43d43f43c43e43h43g533418a18b18c18f3537b37aREF. 12149*66671716

308131 35PartsWARNINGSome PRO 4500sc Gun replacement parts look similar toother PRO Gun parts but are not interchangeable! Whenservicing,

36 308131AccessoriesAIR LINE ACCESSORIESConductive Air Supply Hose; black100 psi (7 bar, 0.7 MPa) Maximum Working PressureFM Approved; Colo

308131 37AccessoriesFLUID LINE ACCESSORIESFluid Hose Assemblies (Nylon)225 psi (14 bar, 1.4 MPa) Maximum Working PressureFM Approved; 1/4

38 308131AccessoriesGUN SYSTEMSGun System 224637With 36 ft (11 m) conductive air hose. Includes:Part No. Description Qty224200 PRO 4500sc E

308131 39Technical DataCategory DataGun Weight 34.3 oz (974 g)Gun Length 11.1 in (283 mm)Maximum WorkingPressure100 psi (7 bar, 0.7 MPa)Ai

4 308131WARNINGFIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARDImproper grounding, poor air ventilation, open flames, or sparks can cause a hazar

40 308131Graco Standard WarrantyGraco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material

308131 5WARNINGPRESSURIZED EQUIPMENT HAZARDSpray from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the s

6 308131Installation0389Non-Hazardous Area Hazardous AreaKEYA Main Air Supply LineB* Ventilation Fan Interlock Solenoid ValveC* Main Air Su

308131 7InstallationInstalling the SystemWARNINGFIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARDInstalling and servicing this equipmentrequires

8 308131InstallationConnect the Exhaust TubePress the exhaust tube (provided) onto the barbedadapter on the bottom of the gun handle. Secur

308131 9InstallationCheck the Electrical Grounding (See Fig. 2)WARNINGFIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARDMegohmmeter P/N 241079 (AA